Seamless Gutter Cost Calculator 2027: Price per Foot

How to Use the Gutter Cost Calculator

You need a tape or a measuring wheel and about ten minutes walking around the house. Gutters only go on the level edges of the roof: two sides on most gable roofs, all four on a hip roof. Measure along the roof edge itself, and include any shingle overhang past the wall at the ends.

1. Length of Gutters. Add up every run in linear feet. The calculator opens at 100 feet.
2. Number of Floors. Count the stories under the gutter line. Taller ladders mean more setup time and more risk, so each downspout costs about two-thirds more once you go up a floor.
3. Gutter Type. The default is standard 5-inch one-piece aluminum. Pick 6″ Aluminum for a big roof or heavy rain. Copper and zinc arrive in 10-foot lengths, so those prices are for sectional gutters, not one-piece runs.
4. Install Leaf Guards. “Yes – Budget” prices basic screens. “Yes – Expensive” prices a premium branded system.

Every estimate includes four downspouts and tear-off of the old gutters at about $1.44 a foot. Corners aren’t a separate field, so if your house has more than four downspouts or a lot of inside and outside corners, plan on the High End figure.

Labor rates follow the location in the calculator’s heading. Use the “change” link there if it’s wrong. Pacific states land about 18 percent over the national average, and the West South Central states (Texas, Oklahoma, Louisiana, Arkansas) about 16 percent under it.

Small jobs have a floor. Crews rarely unload ladders for under about $490, which is also the calculator’s minimum, so even one short run over a back stoop with a single downspout costs close to that.

How Much Do New Gutters Cost?

Standard 5-inch aluminum, formed in one piece per run, costs most homeowners about $1,120 to $1,520 per 100 feet installed. About 150 feet, enough for the front and back of a typical house with a downspout at both ends of each run, comes to $1,740 to $2,310. A quote much past $17.32 a foot on a plain one-story house is padded.

House Size	Approx. Gutter Run	One-Story, Aluminum, 6 Downspouts
1,000 sq ft	about 80 ft	$1,280 to $1,680
1,500 sq ft	about 120 ft	$1,560 to $2,030
2,000 sq ft	about 160 ft	$1,850 to $2,430
2,500 sq ft	about 200 ft	$2,140 to $2,830
3,000 sq ft	about 240 ft	$2,430 to $3,240

Which Gutter Metal and Profile Should You Pick?

About 80 percent of homes end up with aluminum. Installed prices per linear foot:

Metal	Installed Price per Foot	Good to Know
Aluminum	$10.39 to $15.02 (5-inch); $17.32 to $21.95 (6-inch)	Rust-free, light, lots of colors; one-piece runs are K-style only
Galvanized steel	$16.17 to $24.25	Takes a hit well; rust can start in 5 to 7 years
Stainless steel	$28.88 and up	Never rusts, but priced well above galvanized
Copper	$34.65 to $57.75	Soldered corners, copper downspouts, specialist labor
Zinc	$51.98 to $63.52	10-foot half-round sections, special order only

With aluminum, ask for .027 or .032 gauge if you get real snow, and make sure the coil is primary aluminum. Secondary stock is made from recycled metal and doesn’t last as long, and it’s an easy place for a low bidder to save money at your expense.

Steel shrugs off ladders, branches and the odd baseball, but it rusts and usually costs more than aluminum. Stainless fixes the rust and costs too much for an ordinary house.

Copper is formed in one piece as K-style or sold in 10-foot half-round or box sections. Either way the joints are soldered, the downspouts and elbows are copper too, and the price climbs fast on a complicated roofline. Zinc is too hard to form from a truck. It comes in pre-made 10-foot pieces, usually half-round, from brands like RheinZink and OrnaMetals, ordered through roofing distributors such as ABC Supply or Beacon.

Profile and finish. Most homes use K-style, the flat-backed shape whose front looks like crown molding. Half-round is the plain open trough on older homes, and it’s the cheaper one: K-style can cost up to 50 percent more per foot, but it’s deeper and holds about twice the water and debris. Both come in 5- and 6-inch widths (gutters overall run from 3 to 7 inches, and every inch adds metal and cost), so the choice usually comes down to looks and how much rain you get. White and pale colors are the cheapest; darker finishes usually cost extra.

What Happens on Install Day

Labor is about $1.16 to $8.09 a foot of the total bill, depending on the metal, the gutter size and how much climbing and cutting the house needs.

The truck pulls into the driveway with a roll former and a coil of aluminum. Short pieces are sometimes made at the shop, but anything longer than about 30 feet is formed on site, because a piece that long bends and dings on the way over.

Each length is trimmed about 2 inches past the roof edge to catch water spilling off the sloped ends. On the ground, the crew snaps on end caps, punches downspout holes 6 to 8 inches from the ends (or wherever a drain is planned), sets the outlets and seals every joint. Hidden hangers go in every 18 to 24 inches. Then the length goes up and is fastened to the fascia with a slight tilt toward the outlets. Leaf guards follow, and downspouts go on last.

A simple one-story house is often done before lunch. Extra stories, lots of corners or fascia repairs stretch it out.

Two Houses, Two Very Different Gutter Bids

Per-foot averages hide a lot. Here is how the same crew might price two homes.

House A is a one-story ranch with about 150 feet of eave, four outside corners, four downspouts, solid trim and old gutters to remove. The calculator, with tear-off at about $1.44 a foot built in, lands near $2,050, and fair bids run from about $1,820 to $2,420.

House B is two stories with bump-outs: 180 feet of eave, ten corners and six downspouts. The second story raises the cost of every downspout, and each miter is cut, fitted and sealed by hand, the slowest work on the job, so bids land toward the high end. Then the crew finds about 60 feet of soft fascia:

• Gutters and downspouts: roughly $2,720
• Tear-off: around $260
• Fascia replacement, 60 feet: about $990
• Total: somewhere near $3,960

Same metal, same crew, about double the bill. A phone quote based only on square footage is worth very little.

The Fascia Problem Nobody Budgets For

Fascia is the board the gutter screws into. Years of overflow or old roof leaks turn it soft, and a soft board won’t hold a screw, so new gutters on rotten wood sag and pull away long before the metal wears out.

New wood or PVC board, with the old removed, runs about $15.02 to $17.32 per linear foot, and metal-wrapped trim costs about the same. Poke the boards with a screwdriver before you sign anything. If a new roof or siding job is coming, bundle the fascia and gutters into it and pay for setup once.

Hiring a Gutter Crew Without Overpaying

Get three or four bids. It’s the quickest way to spot padding, and it gives you a few references to call. You can get free quotes from local gutter installers and compare them against your calculator number.

Ask whether the company owns its own roll former. Outfits that form gutters in your driveway often charge 5 to 7 percent less.

Before the crew leaves, sight down each run. The outlet has to sit at the lowest point. If it doesn’t, water stands in the trough, and standing water means rot and mold.

Leaf guards help limit ice-dam damage in heavy snow country, but you don’t need a premium branded system. Basic screens from a home center do about the same job for far less and pop off easily for cleaning. If ice dams are a real problem on your roof, add roof heat cable.

Doing It Yourself: Three Ways to Get One-Piece Runs

Home Depot, Lowe’s and Menards sell every part of a gutter job except long gutter. Store stock comes in 10-foot pieces, and every joint is one more place to leak someday. For continuous runs you hang yourself, you have three choices:

1. Buy from a gutter supply shop and haul it home. Their machine rolls out one piece of almost any length. Getting it home is the problem: past about 25 feet, a gutter on a ladder rack flexes at every bump, and one kink ruins it. This works for a garage, shed or other short run, and only if you have a pickup.
2. Pay the supplier to form it at your house. Many suppliers run a truck with a roll former, coil and fittings. The trip adds about $0.25 to $0.50 a foot, roughly $50 to $100 on a normal job, and material still comes to about $4 to $5 a foot with nothing to transport. This is the smart pick for a bigger DIY job.
3. Hire it out. It costs the most on paper, but gutters are one of the cheaper exterior jobs. Most houses come in under $2,310, and a crew finishes a simple one in about four hours. Compare that with renting ladders, scheduling a delivery and spending your Saturday on a roof edge.

Gutter FAQ

Does every house need gutters?

Not always. Their only job is to move roof water away from the house. In a very dry climate with long rainless stretches, some homes do fine without them. Anywhere with steady rain and snow, like the Northeast, they protect the roof, walls and foundation.

Are one-piece gutters worth the extra money?

For most homes, yes. Fewer joints means fewer leaks. A working system keeps water off the foundation, walks and driveway, stops washouts in the flower beds, lowers the odds of a wet basement, keeps siding and trim from rotting and cuts down on ice-dam damage.

What else should I price with new gutters?

Anything that shares the ladder setup. If the roof is near the end of its life, run the roof replacement calculator or check metal roof prices first, since gutters usually come off for a reroof. For the trim, price the paint job with the exterior painting calculator.